• The Canon Rumors Forum has officially been shut down as of July 10, 2026.

    All data will be deleted on September 16, 2026.

    the ad free experience will return by July 17, 2026.

Pocket Wizard Canon firmware update 6.150 problem

  • Thread starter Thread starter Andrew Fox
  • Start date Start date
Status
Not open for further replies.
Sort by date Sort by votes
A

Andrew Fox

Guest
#1
Just updated Mini TT1 & Flex TT5 firmware to 6.150 for Canon Speedlites. Now flashes can't be triggered. When camera is fired Mini TT1 blinks red twice. Have used different combinations of 580 EX and EXII and 600 RT. Have reinstalled firmware in all three TT5 units and changed battery in Mini TT1. Any ideas?
 
#2
which camera are you using. if it is a 5d mark3 or a 1Dx it will not work yet.

if not using one of those cameras make sure you set them to automaticlly select the camera model and they are sync'd with all having the same channels and settings selected on the setting 1 or 2.

if that doesn't work reset them to factory settings and try again.
 
Upvote 0
#3
Andrew Fox said:
Just updated Mini TT1 & Flex TT5 firmware to 6.150 for Canon Speedlites. Now flashes can't be triggered. When camera is fired Mini TT1 blinks red twice. Have used different combinations of 580 EX and EXII and 600 RT. Have reinstalled firmware in all three TT5 units and changed battery in Mini TT1. Any ideas?
Click to expand...

I've noticed that Firmware updates, whether an upgrade or downgrade, could result in the PW's not working 100% correctly. So I got in the habit of always doing a factory reset after a firmware change, then manually setting all my configs (and duplicating) as appropriate.
 
Upvote 0
#5
I didn't realize the firmware was updated yet for 5D3. I've been on the list to get notified by PW of the new update. Whaz up?

In the interim, I purchased the Phottix Odin set and they work fine for 5D3 with 580ex, 580exII's. They were a bit cheaper, run on AA batteries, but have a few more buttons to push to adjust levels.

Good luck
 
Upvote 0
#6
I spent nearly three years with my PW's to make them work, they never did, and always something different that was wrong. I even swapped them for new units, and new flashes , same crap all over.

I got the word on the Phottix Odin and I have used those for over 7000 images now, not one single misfire!! Still full battery on the transmitter (c r a z y ) I couldn't be happier. You take them out of the box, put the batteries in, done. Go shoot and have fun!

And they also have remotecontrol over power from trigger to reciever. Fantastic feature, and it worked with the 5d3 straight away. Manual works for the 1d X, but full ettl support is being worked on. (they can still use the ettl communication line, so remote poweradjustment is still working)
 
Upvote 0
#8
I have pocket wizards flexs and mini and am disappointed like others with random misfires at events and the fact my 5d2 was only able to fire my two 580ex II not my new 5d3 in ettl. I am thankful I realized this toying around at home not at an event. Needless to say I soured on pocket wizard and jumped on the highly praised photix odin parade, my experience wasn't as well as some others. Odin transmitter had many features than the PW however it looked cheap in on top of my camera in my opinion but functionality matters most and it all seemed great but my unit had a defective casing, I received a replacement unit and that unit was unreliable and had several issues with flash not going off. I am sticking with the pocket wizards for now.
 
Upvote 0
#12
After further investigation:
I have two 5d. Everything worked fine till the latest firmware update then:
If I put a mini or a flex on one 5d everything works, on the other one I got a misfire and two red blink.
Now the strange thing. If I put the mini on the first 5d trigger fine and then move it on the second 5d it works flawlessly!
Seems like the first 5d sorts of initialize the mini whereas the second is not able to...
Hope this helps.
Max
 
Upvote 0
#14
I posted this a few minutes ago on a topic that was similar regrading pocket wizard beta update 6.153. Hope this helps because I know it's been driving me crazy since up got my 5d3.


First time poster long time lurker. Want to say thank you for this post Justsomedude. I've been waiting for this firmware update for months as I have missed some of the functions that pocket wizard offers. Manly the AC3 zone adaptor. I would also like to say thanks to a few posters that I have learned so much from in the past. Namely Bosman, Mt. Spokane Photography, Neuroanatomist, and V8Beast to name a few. I can confirm that the Flex TT5 and Mini TTI along with the AC3 zone adaptor seem to work with the 5D3 and 600EX-RT's. You can use the AC3 to fire the flash in different groups and also adjust the power setting for both manual and ETTL. I've only ran a few tests. One of the things that I did notice is that while the flash seems to fire on the power setting you set from the AC3 the back screen on the 600 doesn't change. It says it's in ETTL at no compensation. Even when you are in Manuel and power the flash all the way down on the AC3. I also noticed that the IR beam doesn't work to help focus on the flashes. You might be wondering why I would need the pocket wizards if I paid the money to get the radio function in the 600. It basically comes down to the fact that I have ST-E3-RT and while it's great it is not as simple to change power settings, zones, manuel to ETTL in different zones as the AC3. Second reason is that I also have a couple Einsteins that I love to use with the Canon flashes and again the AC3 has no equal that I've seen. I will be doing a larger test tomorrow at the beach with my kids to see if some of the old problems pop up that I use to have with the 580's. I'll post the results. Thanks again....
 
Upvote 0
#15
Warning regarding this update: I recently applied it to my TT1 which I use to trigger the PowerMC2 receivers on my Einstein640s. I was shooting with the 1Dx and everything seemed to be working well until I tried some High Speed sync, which wouldn't work.
I applied the update to discover that now the TT1 wouldn't fire on my 1Dx. I then read the release notes (I know...facepalm) and discovered the update of course doesn't support the 1Dx. Oh well I'm about to start a shoot so I swap to the 1Ds MKIII. Doesn't work. Test button fires the flash but the cameras won't. Swap to 1Ds MKII, which works but only syncs a 1/60.
I course don't know if this applies to all combinations of Mini TT1 and receiver with te canon 1Ds line but if you are using this combo I would definitely hold off on the update as there appears to be NO way to ROLLBACK the firmware.
 
Upvote 0
#16
rawbphoto said:
Warning regarding this update: I recently applied it to my TT1 which I use to trigger the PowerMC2 receivers on my Einstein640s. I was shooting with the 1Dx and everything seemed to be working well until I tried some High Speed sync, which wouldn't work.
I applied the update to discover that now the TT1 wouldn't fire on my 1Dx. I then read the release notes (I know...facepalm) and discovered the update of course doesn't support the 1Dx. Oh well I'm about to start a shoot so I swap to the 1Ds MKIII. Doesn't work. Test button fires the flash but the cameras won't. Swap to 1Ds MKII, which works but only syncs a 1/60.
I course don't know if this applies to all combinations of Mini TT1 and receiver with te canon 1Ds line but if you are using this combo I would definitely hold off on the update as there appears to be NO way to ROLLBACK the firmware.
Click to expand...

UPDATE: Pocket Wizard sent me firmware file that allowed me to take it back to version 6.0. No hi speed sync with the 1dx but at least it does fire up to 1/125.
 
Upvote 0
#17
I agree, I have 3 Flavrs of wizard PW II 4 of them, PW TT5 4 of them and 2 multi-max's


PW II fire 95% of the from Good distances

Multi max fire about 75% from may be 60 feet away

and teh DAMNED TT5's are sketchy on a good day, Jesus premium cost with sketchy reliability, maybe my fault for using 580 II

Now with my Nikon SB 28's they almost never fail with the PW II's its almost liek you need a SHOE extension to get that PW away from the Canon interference .

It woudl be nice to see what the RF interference bubble is like on a CANON 580 vs a 430 and to nwo its AREA of effect, thus allowing us to PLACE out PW's in better places if we can.


Now im waiting on 1D X worried there will be a new batch of problems, jeez man.
 
Upvote 0
#20
I had a really bad time with my pocketwizard flextt5's at the last wedding I shot. They were rigged to fire strobes in trigger mode, and one or both of them would stop working seemingly at random. I turned them off and just used bounce flash the rest of the night.
 
Upvote 0
Status
Not open for further replies.
Top Bottom
Home
Forums
Media
Menu